SIG CA THIN is thin as water and cures very fast, normally in 1-3 seconds. Thin CA is used to glue together parts that fit tightly together with no gaps, and that do not require repositioning after the glue is applied. Typically the two parts are mated first, and then Thin CA is flowed along the joint. Capillary action wicks the Thin CA deep into the joint, resulting in a very strong bond. Thin CA sets very rapidly, so do not expect to move parts at all after the glue is applied. Thin CA is ideal for tack gluing assemblies together quickly on the building board (later the joints should be re-glued with Medium CA). Also good for repairs where you have a lot of cracks or torn wood fibers to be glued together. The Thin CA wicks into every nook and cranny of the break and ties the fibers together almost like new. Thin CA can also be used for applying fiberglass cloth reinforcing. Thin CA is the only glue that should be used on SIG EASY HINGES

SIG CA MEDIUM is medium viscosity and normally cures in about 5-15 seconds. Medium CA is the general purpose favorite, excellent for almost any step during construction. Many people use it for the majority of their construction. Can be used on less than perfect joints, filling in the minor gaps between the parts. Medium CA can be flowed into an already assembled joint (ala Thin CA), or it can be used more like a traditional glue by applying it to one part before it's mated to the other part. Also good for re-gluing joints that have been tack glued with Thin CA.

SIG CA THICK has a thick, syrupy viscosity and the slowest setting time, normally curing in 30-90 seconds. Typically Thick CA is applied to one part before mating to the other part. Longer cure time allows you a few seconds to position the part before the Thick CA "goes off". Cure can be quickened with the use of "accelerator" once the part is positioned. The thick consistency reduces the tendency to run and fills gaps between parts. Ideal for gluing large parts like wing sheeting and fuselage doublers. Can also be used to build up strong fillets around joints requiring extra strength.

SIG KWIK-SHOT CA ACCELERATOR - While CA glues are faster drying than any other type of modeling glue, there are still times when we wish we could make it dry "on command". That's where CA ACCELERATOR comes in! It's a special liquid, that comes in a small spray bottle, that makes any type of CA glue set instantly on contact! CA ACCELERATOR is sprayed onto the joint after the glue is applied and after the part is in final position. The ACCELERATOR chemically reacts with the glue causing it to set immediately. ACCELERATOR is most often used with Medium or Thick CA - it should not be used on Thin CA (which dries almost instantly all by itself). Spray on the ACCELERATOR sparingly! Too much can cause CA glue to react too rapidly and literally boil. This will result in a joint with a chalky white color which is not nearly as strong as a normal joint.

SIG CA DEBONDER - A special chemical that softens and loosens dried CA glue so you can un-stick things you didn't mean to glue together - like your fingers! Apply DEBONDER to the area and wait for the glue to soften. Don't rush it! It may take 20 to 30 seconds of soaking to get your fingers back apart. For a thick buildup of glue, you may need several applications of DEBONDER to remove it all.

Core-Bond is a special water-base adhesive for bonding any type of wing skin to a foam wing core. Core-Bond works equally well with balsa wood, plywood, or plastic wing skins. It’s the best choice for beginners at foam wing covering because it is so easy and safe to use. Will not melt foam when used as directed. Experts like Core-Bond’s relatively fast drying time and light weight. It has a unique viscosity that keeps absorption into the foam and balsa to an absolute minimum, resulting in the lightest bond possible, without sacrificing strength. Tests prove that the strength of the bond will exceed the strength of the balsa material. Core-Bond can be applied with a brush, roller, or spatula. Important Note: Core-Bond is damaged by freezing. We cannot ship during cold weather. Order adequate supply in advance

SIG CONTACT CEMENT A HANDY ADHESIVE FOR THE MODELING WORKSHOP: Bonds wood to wood, metal to wood, metal to metal, cloth to wood, cloth to metal, and many other combinations. To use, apply one coat to each surface, allow to dry to the touch, press parts firmly together. Use only for broad area bonding, do not use for butt joints. Do not use on foam!

Epoxy glues should be used any place that extra strength is needed, such as firewalls, engine bearers, landing gear mounts, and the interior of the engine compartment. Kwik-Set epoxy is also very valuable for field repairs as it gives an extremely strong bond in just 5 minutes. It should be in every modeler’s field box.

Light Weight - Strength of Epoxy - Quick Setting - Easy To work - Good Paint Adhesion - Long Shelf Life. A unique material that was developed specifically for model airplane work. Makes beautiful wing and tail fillets, repairs in balsa, fills dents in foam wings, or can be used to mold strong, light weight parts. Fill seams in ABS plastic parts and cowlings. EPOXOLITE does not shrink and sticks with the strength of epoxy glue. Excellent bonding with dope, enamel or epoxy paints

KWIK SET 5-Minute Epoxy Glue

Recommended uses for Epoxy glues::

• Epoxy glues are completely fuel proof, making them an excellent choice for coating the engine compartment and other areas of your models that need extra fuel resistance.
• Epoxy glues incredible strength makes it the best choice for gluing wing spars, firewalls, landing gear blocks, and other areas needing extra strength.
• Bonds balsa to balsa, hardwood to hardwood, hardwood to balsa, metal parts to balsa or hardwood

Sig Micro-Balloons are expanded glass beads, microscopic in size. They are so small, they have the appearance of powdered sugar and are extremely light. They make a strong light weight putty when mixed with Sig-Ment, Sig Polyester Glass Resin, or Sig Epoxy Glue. Instructions for mixing are on the container

SIG-BOND is an aliphatic resin model airplane glue that makes model building easy! It’s the traditional general purpose wood glue that model builders have loved for years because it is so safe and easy to use. Non-toxic. Cleans up with water. This glue is super strong and will permanently bond all types of wood. The joint will undoubtedly be stronger than the wood itself! Recommended for the assembly of all the wood parts of a model structure. Air dries in 20-30 minutes and sands very well. Completely dope and lacquer proof. Sands Smooth & Clean, Extra Strong Joints, Fast Dying Dope and Lacquer Proof Recommended Uses:: General framework assembly, Balsa to balsa joints, Hardwood to balsa joints, Hardwood to hardwood joints, External planking seams.

CA Applicator Tips

For mixing and applying epoxy, stirring paint, mixing Epoxolite and many other uses.

Many times in the shop you’ll have a need for a small, inexpensive brush. These 3/8” wide nylon bristle brushes are handy to have around for spreading epoxy glue, wood glue, contact cement, fiberglass resin, or any other liquid for that matter. Economical enough to throw away! Also ideal for cleaning engines, wheels, landing gear wires, and other metal parts. Impervious to any solvent. Five inch long metal handles

A convenient 1/2 oz. plastic syringe for dispensing model cement, aliphatic resin glue, white glue, or epoxy glue. Allows you to precisely control the amount and placement of your adhesives for a lighter, neater building job. Also handy for injecting glue inside splits and breaks when repairing crash damage. Extremely small, pointed tip is tailor made for those hard to get at places on a model. The curved tip makes it possible to go around corners and into blind spots. This is a top quality mini glue gun that will give you years of service if you clean it thoroughly after every use.

This handy flexible plastic tool is just what you need when working with glass resin or epoxy glue. Lots of uses! Allows you to lay on a thin, smooth coat of glue where you want it. Great for working glue or resin into dry glass cloth until full saturation is achieved. Then use it as a squeegee to scrape off the excess glue and push the glass cloth tightly against the surface. Helps you keep weight build-up from excess glue to a minimum. Clean up the EPOXY SPREADER with alcohol before the glue dries and one spreader will last through several projects

These are clear plastic cups suitable for all epoxies, polyesters, or whatever you would like to use them for. You can accurately measure any amount from 1/4 to 1 full ounce. For convenience, the cups are marked in fluid ounces, drams, milliliters, and tablespoons. So any measurement you are comfortable with, you can use.

SIG-MENT is a traditional solvent-based model cement that is fast drying and fuel proof. An old-time favorite for all-around model construction. Especially recommended for light-weight F/F models. Great for gluing ABS and some other plastics to balsa wood. Sands easily!

Liquid Resin Glue. It is strong, dries clear and is recommended for Balsa to Framework assembly, Hardwood to Balsa and Hardwood to Hardwood