MARINE NAVAGATION LIGHTS

LIGHT BAR/POLICE STYLE

The molded plastic light bar is 4" long with a chrome base and 2 red lenses, perfect for 1/10 and 1/12 scale vehicles. The system includes an adjustable rate flash unit with two bulbs, each on 12" of wire. A 9 volt battery snap is provided or 6 cell car nicads can be used. Blue and amber lenses are available from RAM.

"GAS CAR HEAD, TAIL & STOP LIGH"

Designed to provide an efficient 9 volt alkaline battery powered lighting system for gas powered cars and trucks. The system includes two of our #19 type headlights for easy installation. Two red tail lights, controlled by a micro switch, shift to bright stop lights anytime the throttle linkage drops from full power. Installation details and tips are included in the instructions

Two white LED headlites and 2 red LED tail lites, each on 1 foot of wire are powered by 6 or 7 cell nicad packs or for over 4 hours by a 9 volt alkaline battery.

Adj. rate. Two 48" wires provide for up to 96" wing span and attach to a Deans connector to allow detachment from the fuselage, the switch and the 36" wire to the tail lite. Red, green and clear lens caps provide proper navigation colors. The small circuit board allows for adjustment of 50 to 80 flashes per minute. Weight, approx. 1 oz.

Adj. Rate A white LED on 3 feet of wire attached to a circuit board provides a strobe effect. Includes a 3/8" diameter clear lense.
Weight approx. 1/2 oz ...............

HEADLIGHTS FOR TAMIYA

Designed for Tamiya etc. molded grills. Two bayonet style, 1/4" bulbs, each on 12" of wire, allow easy installation. Comes with a 9 volt battery snap or 6 cell car nicads can be used.

MAXX HEAD & TAIL LITES

This system has two Ultra Brite white LED head lites with 2 red tail/stop lites controlled by a switch attached to the throttle servo and powered by a 6, 7 cell Nicd or a 9V alkaline (6 hours). Wire lengths and instructions offer installation on most popular Maxx gas and electric chassis

CAR HEAD LIGHTS

The aluminum 5/8" diameter reflector protects the bulb in the toughest crash. Two lights, each on 12" of wire, allow easy installation. Comes with a 9 volt battery snap or 6 cell car nicads can be used.

CAR TAIL & STOP LIGHTS

This system is comprised of two red stop lights, each on 12" of wire, and a switching device that is simply wired to the electric vehicle's drive motor. Whenever forward power is reduced, the bulbs will go from a dim tail light to a bright intensity for brakelight effect. No power is drawn from the motor battery 9 V battery powers the system

CAR TURN LIGHTS

Four amber lites are used to duplicate scale vehicle operation. Two microswitches control a flasher device to simulate turn light action automatically when the vehicle is maneuvered. Comes with a 9 V battery snap or 6 cell car nicads can be used

REAL STROBE LIGHT

This is the smallest, lightest, safest, xenon strobe ever offered to the R/C modeler. The unit is 3/4 " X 1 " x 1 1/2". The encased flash tube is 1/8" x 1 " on a 10" cord. Total weight, 1 oz., under 3 ounces with 2 AA cells which will power the unit up to 8 hours. Comes with battery box and a clear lens cap.

RAM LITES

Two off road style, all aluminum lights for roll bar or body mounting. The black anodized 1/2" long threaded base provides easy mounting. The 1 " diameter satin finished body can be used as is or polished to a high gloss. A 9 V battery or 6 cell car nicads can be used.

RAM LITES FOR TAMIYA ROLL BAR

Two #24 RAM Lites are packaged with two adaptors which mount to the Tamiya or similar roll bar.

RAM LITES W/FOLD AWAY ROLL BAR

Now you can have a roll bar that won't tear up your light plastic truck bodies when they roll over. Two #24 RAM Lites are supplied with adaptors and all hardware to make a fold away roll bar which adapts to any R/C body.

3 WAY SIMPLE SIREN

This compact but loud system offers a choice of three distinct siren sounds for cars, boats, and planes. The system comes with a 2" speaker. Weight 3 oz. Requires a 9 volt alkaline battery

PACE CAR 10 LIGHT SET

Add the excitement of a Pace Car to your collection of car bodies. This set includes 2 #19 Headlights with aluminum reflectors, 2 tail lights with red lenses, 4 flashing hazard lights with amber lenses and a RAM 07 Light Bar with 2 flashing bulbs and an adjustable rate flasher all wired into one system. You can use a 9 volt alkaline battery or a 6 cell car nicad pack for power.

CAB MARKER LIGHTS

These assembled, scale lights are 1 inch long, have amber lenses and are ready for quick installation. They are aluminum, rugged and AMERICAN MADE. The 5 light set uses a 9 volt alkaline battery or your 6 cell car pack.

"GAS/DIESEL ENG SND/HORN 4"" SPK"

You choose either a gas or diesel engine sound with adjustable horn for your electric car, truck or boat. Idle rate and top speed are also adjustable. Simple 4 wire hook up. Completely assembled, includes 4" speaker. Compact state of the art design is synchronized to motor speed. 6 to 14.4 volt input power. Perfect for 1Oth scale cars and trucks, Dumas Chriscrafts and Tugs, Midwest Trawlers etc.

"GAS/DIESEL ENG SND/HORN 2"" SPK"

Uses the same sophisticated sound device as the RAM 38 but with a 2" speaker to allow installation in smaller cars and boats.

SERVO FAIL SAFE MARK II

Save your model and maybe more! Anytime your model loses transmitter signal, this device will automatically move the servo it controls to the failsafe position you have preset. Example: Stop or reduce the engine throttle and greatly minimize the chance of severe crash damage. Response delay is adjustable from 0 to 5 seconds. It is also WATER PROOFABLE and features a flat design that is half the size of a credit card. This new version has two generic connectors and will work with any receiver.

XTRA CONTROL

Modelers are now able to turn on lights, sound horns and operate a wide variety of accessories without investing in more expensive radios or channel expanders. The mini receiver (1 " x 2 1/2" X 7/8 ") and "key fob" transmitter have a range to 100 feet and provide a latching on - off function AND a momentary function. Each can carry a load of up to 1 amp. There is also provision to simply individualize the system so that it will not interfere with another modelers X Tra Control radio.

RAM FLASHING NAVIGATION LIGHT

The Flashing Nav electronic circuit simulates the flashing of Red and Green wing lights with a Strobe in the tail.

This system now features wing light wires to provide for a span of 94 inches which will accommodate 90% of the model kits currently available. A Deans connector provides for easy wing removal.
The flash rate and duration of the red and green wing tip lights and the clear tail light are adjustable through a wide range to duplicate any scale operation. The assembled system contains the flasher circuit board with a 9 volt battery snap, connected to the wires and bulbs described above.
Approximate weight, 1 ounce.

RAM STROBE LIGHT

The Adjustable  Rate Strobe Light electronic circuit simulates a Strobe effect.

The light is adjustable to any desired flash rate. The system contains an adjustable rate flasher circuit board, 1 high intensity bulb on three feet of wire, battery snap connector and a clear dome lens. The system provides a bright, adjustable strobe light effect. Weight approximately 1/2 oz.

RAM LANDING LIGHT

The RC Landing Light system electronic circuit allows you to control the lights ON and OFF from your transmitter.

System contains a positive pulse electronic switch and 2 high intensity bulbs with fixtures. It is connected to the receiver to work independently or simultaneously with another control function and uses the 4.8 volt RX. pack for power. Weight approximately 1 oz., with generic receiver connecto

RAM MARS ROTATING BEACON

The Mars Beacon electronic circuit simulates the rotating effect.

The light is adjustable to the desired "rotation" rate. The system contains an adjustable "rotation" unit, 1 high intensity bulb on three feet of wire, battery snap connector, and one red dome lens. Weight approximately 1/2 oz.

RAM MARINE NAVAGATION LIGHT

(Non-flashing, may be used for some aircraft types)

RAM SKYLIGHT 18 LIGHT 7.2-9V

The Sky Light set consists of 3 strands containing 6 bulbs each.

This system is the proven way to fly at night or in low visibility. Three light strands, containing 6 bulbs each, are used to light each wing and the fuselage so flight orientation is maintained with the familiar "T" shape of a lighted plane against a black sky The model must be of "built up" construction with little planking and covered with a translucent material such as made by Monokote. The assembled system provides for models up to 94" span and includes a Deans connector to detach the wing and a master switch. Using a 7.2 to 9 volt battery will result in a total glowing effect that cannot be matched by any other light system.

RAM BATTERY BACKER

BATTERY BACKER. Radio manufacturers state that battery pack and switch failure account for 80% of all radio problems. The system provides a complete backup for both of these trouble sources. The device senses low or intermittent voltage from the main receiver battery system and instantly switches to the backup battery system. (This battery can be as little as a 100 milliamp nicad pack or a standard nicad or alkaline pack.) It then turns on a bright red LED so that you are warned that you are on the backup system. The backup battery and switch harness are required to complete the installation. The 3 amp system capacity is suitable for models using 4 standard servos. Larger models with heavy duty and dual servos should use the RAM 25. The device is 1 1/4" x 1/4" x 5/8". Weight 1/2 oz. Now with generic connectors for "plug and play" installation.

RAM FLASHING LED LITES

FLASHING NAVIGATION LITES Adj. rate. Two 48" wires provide for up to 96" wing span and attach to a Deans connector to allow detachment from the fuselage, the switch and the 36" wire to the tail lite. Red, green and clear lens caps provide proper navigation colors. The small circuit board allows for adjustment of 50 to 80 flashes per minute. Weight, approx. 1 oz.

RAM [STROBE] LED LITES

"STROBE LITE". Adj. Rate. A white LED on 3 feet of wire attached to a circuit board provides a strobe effect. Includes a 3/8" diameter clear lens. Weight, approx. 1 oz.

RAM LANDING LED LITES

LANDING LITES. Two white LEDs, each on 2 feet of wire are connected to a micro switch which can be controlled by the throttle, flap or retract servo. Weight, approx. 1 oz.

RAM NAVIGATION LED LITES GAINT SCALE

NAVIGATION LITES, GIANT SCALE. Two 6 foot wires attach to 2 Deans plugs and 1 foot wires to provide up to 168" span. These attach to the switch and a 6 foot wire to the tail lite. Red, green and clear lenses provide proper navigation colors. Approx. weight 2 oz.

RAM NAVIGATION LED LITES NON- FLASHING

NAVIGATION LITES, NON FLASHING. All of the same features of the RAM 121 above but without the flasher circuit board. Approx. weight 3/4 oz

PARK FLYER NITE LED LITES

This 6 gram, 3 lite system uses Ultra Brite LEDs with red green and clear lense caps for easy orientation and draws only 6 ma for a typical 10 minute flight from your 5 to 8 cell power battery. Simply tape the system to a park flyer up to 48" span and enjoy flying early or late when the wind conditions are most friendly.

System contains 3 superbright bulbs, with red, green and clear lenses, a six-foot tail lead, 2 sevenfoot wing tip leads with Deans connectors, switch, and a 6 AA cell battery box. Nicad or alkaline cells are required. Weight 3 oz.

This set provides for models not needing flashing lights and also features wing wires for up to 94" models and a Deans connector for easy wing removal. Instrument bulbs with red, green and clear lens covers are powered by an alkaline 9 volt battery or a 6 cell nicad pack. Approximate weight, 1/4 ounce.

System contains 2 superbright bulbs rated at 2800 beam candlepower each on 2 feet of wire, with new, 5/8" diameter, aluminum, focused reflectors, microswitch, battery snap connector. Switch attaches to retract, flap, or motor servo for control. Weight 1 oz.

RAM BIG PLANE RF DE-GLITCHER

These small beads (1/4" x 7/8") eliminate the use of bulky and expensive chokes to protect your radio from long servo wire RF interference. The 10 beads in each package are usually enough to protect 5 servos in a typical installation. Instructions include a mini-course in glitch elimination.

RAM SIMPLE CYCLER

Why pay for another charger when you already own one? Cycle up to 600 MA, 4.8 volt receiver and 9.6 volt transmitter batteries the easy way throughout the year. The Simple Cycler gives you an audible warning when your packs are discharged to the level recommended by battery manufacturers. Then safely recharge with your radio system's charger. You can easily determine the percentage of use and charge remaining in your pack, as well as get an early indication of cell failure. For receiver packs higher than 600 MA see the RAM 26.

RAM REAL STROBE LIGHT 3V

This is the smallest, lightest, safest, xenon strobe ever offered to the R/C modeler. The unit is 3/4 " X 1 " x 1 1/2". The encased flash tube is 1/8" x 1 " on a 10" cord. Total weight, 1 oz., under 3 ounces with 2 AA cells which will power the unit up to 8 hours. Comes with battery box and a clear lens cap.

RAM BIG BATTERY CYCLER

Now you can cycle your big 4.8 volt packs (600 to 4000 MA) with the same efficiency of our famous RAM 22 Simple Cycler.

RAM DUAL IGNITOR SYSTEM

For 2 cylinder engines with all the features of the RAM 49 and 50. Uses a 2500 MA Sanyo Cell and 2 DuBro plug connectors. 1 1/4" x 2" x 2", 5 oz.